Hacking the Xaar 128 printhead
Re: Hacking the Xaar 128 printhead
The pinout is the same for all XJ128 heads, no matter if 80 or 40 pl, wetting or non-wetting. There is no way to determine in software which head is installed.
Re: Hacking the Xaar 128 printhead
Yes, you are right. I make confusing with Xaar 128 720T.
-
- Posts: 10
- Joined: Tue Jan 24, 2017 6:37 am
Re: Hacking the Xaar 128 printhead
"nfire" signal can can be given independently wheather loading data or not...........if we load data and give firing more than one time wt happend?if it take previous loaded data for all fire or one time it will fire load data ...remaining times it just cleans the nozzles ........
Re: Hacking the Xaar 128 printhead
Wonko
has there been any further progress hacking the 128 - or have you given up with the XAAR
have you got it going in your pwdr printer ?
M
has there been any further progress hacking the 128 - or have you given up with the XAAR
have you got it going in your pwdr printer ?
M
Re: Hacking the Xaar 128 printhead
Hi Moriarty. I did finish a related project with the Xaar head recently, but I am not in the position to publish the result. Sorry. All that was written here pretty much contains all the information needed to make the head work very easily. It's a fantastic head that is very easy to control, fast, and reliable. The piezzo technology makes it perfect for a huge range of chemistry.
Here is a little list of things that make life so easy with this head:
- it uses a standard serial port interface that allows multiple heads to be daisy-chained
- it needs only two constant power supplies
- it doesn't heat the ink
- connectors are easily available in small order sizes
So all that is required is a simple CPU a la Arduino and ten or so wires to control and run this head.
Disadvantage: 150 Euros per head.
Here is a little list of things that make life so easy with this head:
- it uses a standard serial port interface that allows multiple heads to be daisy-chained
- it needs only two constant power supplies
- it doesn't heat the ink
- connectors are easily available in small order sizes
So all that is required is a simple CPU a la Arduino and ten or so wires to control and run this head.
Disadvantage: 150 Euros per head.
Re: Hacking the Xaar 128 printhead
thanks for the reply - a few Q'sWonko wrote:Hi Moriarty. I did finish a related project with the Xaar head recently, .
+ were you able to achieve the quoted firing rates - 4/8kHz for 80/40pL units ?
+ are these achievable on Arduino UNO or do you need DUE ?
+ best price Ive seen is 186 euro (below) any other recommendations ?
http://www.digiprint-supplies.com/en/xa ... 128bt.html
M
Re: Hacking the Xaar 128 printhead
Answers:
1. I have never tried to achieve the firing rates, simply because my transport is too slow. But a fast CPU, preferably suing hardware SPI, is needed
2. I recommend using the Teensy. They are much more powerful in every aspect.
3. Yes, that's where I order them. No complaints.
BTW: adapter boards make life so much easier. This one allows a standard flat ribbon connection to the Xaar head.
1. I have never tried to achieve the firing rates, simply because my transport is too slow. But a fast CPU, preferably suing hardware SPI, is needed
2. I recommend using the Teensy. They are much more powerful in every aspect.
3. Yes, that's where I order them. No complaints.
BTW: adapter boards make life so much easier. This one allows a standard flat ribbon connection to the Xaar head.
Re: Hacking the Xaar 128 printhead
I started to play with an used xaar128. Can I run purified water instead of ink while I make some tests? I don't have capping yet and I just wish to make sure it is working and I can control it. Water won't make deposits and no cleaning cycles required, right?
Re: Hacking the Xaar 128 printhead
Sure. Purified water should work. For a test print, get paper that changes color when it gets wet. The Xaar drops are pretty tiny, and you won't see water drops on regular paper. I tested my setup for hours because I thought it wasn't printing. In the end, I tried black ink, only to realize that I was printing correctly all the time, but I was too blind to see it... .
Re: Hacking the Xaar 128 printhead
Thank you! I was thinking to print on a piece of glass!