https://www.pannier.com/industrial-prin ... -printers/
https://www.videojet.br.com/br/homepage ... nters.html
Hacking the HP45
Re: Hacking the HP45
Last edited by inkjet on Wed Nov 13, 2019 10:29 pm, edited 2 times in total.
Re: Hacking the HP45
There are several ways to build the printhead with speeds, with the same qualities whether Altera, Xilinx, Arm, Atmega and Pic all work perfectly.
Last edited by inkjet on Thu Nov 07, 2019 1:44 pm, edited 1 time in total.
-
- Posts: 11
- Joined: Wed Jul 17, 2019 8:40 am
Re: Hacking the HP45
@Dragonator Excellent suggestion of wiping the head. My HP45 cartirage is a modified one ,it's a solvent based ink not water based. So it was hard to judge what happened while firing the signals.dragonator wrote: ↑Mon Oct 07, 2019 5:00 pm I cannot judge whether the pins are connected correctly, but overall it seems like the right thing. I would lower the delay between clock 1 and clear 0 to 2 microseconds, but other than that, it seems fine.
Do wipe the head before printing. It will literally not work without it. Other than that, I cannot see why it would not work.
Tried to put delayMicroseconds(2) for Primitive Clock and delayMicroseconds(1) for Primitive Clear. Will share the video of it.
- dragonator
- Site Admin
- Posts: 597
- Joined: Fri Aug 14, 2015 4:48 pm
- Location: The Nethelands
- Contact:
Re: Hacking the HP45
I manage 50mm/s at 600 DPI. This gives 1200 firings per nozzle per second.MAsic12345 wrote: ↑Wed Oct 16, 2019 5:33 pmwhat is the speed of spitting HP 45
how fast can they fire?
what speed did are you achieve
-
- Posts: 116
- Joined: Sat Aug 25, 2018 5:26 pm
- Location: Poland
Re: Hacking the HP45
How many amperes consumes HP 45?dragonator wrote: ↑Sun Oct 20, 2019 4:07 pmI manage 50mm/s at 600 DPI. This gives 1200 firings per nozzle per second.
Re: Hacking the HP45
https://www.idtechnology.com/products/t ... clearmark/
https://www.domino-printing.com/pt/products/g-series
https://www.domino-printing.com/pt/products/g-series
Last edited by inkjet on Wed Nov 13, 2019 10:28 pm, edited 2 times in total.
- dragonator
- Site Admin
- Posts: 597
- Joined: Fri Aug 14, 2015 4:48 pm
- Location: The Nethelands
- Contact:
Re: Hacking the HP45
Each nozzle does 300mA, and I can fire at most 5 at a time, so the peaks are around 1.5A. Average should not go above 1A.
@inkjet:
Your schematic shows a pulldown on the address. However, my experience is that I needed separate resistors pulling down when I used led drivers. Adding something like 2k2 fixed the problems. How big would the address pulldowns be in reality? Where did you get most of the information you are sharing?
Re: Hacking the HP45
Last edited by inkjet on Wed Nov 13, 2019 10:26 pm, edited 2 times in total.
-
- Posts: 11
- Joined: Wed Jul 17, 2019 8:40 am
Re: Hacking the HP45
Is anybody heard of XMOS microcontroller. As i have read it has parallel processing capabilities with programmable I/O control. Its mainly a software based control. 200mhz operating frequency is useful when we deals with timing critical signals. I hope it would a better alternative to FPGA as well as suitable MCU for driving HP45 cartirage.
Reference : https://www.eejournal.com/article/20150401-xmos/
Reference : https://www.eejournal.com/article/20150401-xmos/
Re: Hacking the HP45
Hello Inkjet
you posted photos about lot's of interesting boards. However you hid the information necessary to search for more info about these boards.
This is fair, if you can't share these info, however the photos themselves are not useful to us, unless you explain better what function they do and possibly how can we procure them....
you posted photos about lot's of interesting boards. However you hid the information necessary to search for more info about these boards.
This is fair, if you can't share these info, however the photos themselves are not useful to us, unless you explain better what function they do and possibly how can we procure them....