Hi
I am planning to modify my Creality Ender 3 with the Plan B firmware. Here is my plan.
1. Use the stock Ender 3 X,Y,Z motors, end stops, heated bed and thermistors.
2. I have a MKS V1.4 controller board with Marlin 2.0 which I plan to flash with the Plan B firmware after making the necessary modifications to the firmware.
3.Instead of using powder and binder, I plan to use an UV curable ink
4. Rather than making the build platform, my plan is to move the Z axis upwards step by step and cure each layer using UV lamp on the Ender 3 bed itself.
5. I have already the ordered the HP C6602a and carrier, printed the Plan B Inkjet control board and few other components
I would like to get opinion of experts in this forum about the feasibility of achieving the above. Thanks in advance.
Modifiying Creality Ender 3 with Plan B
- dragonator
- Site Admin
- Posts: 597
- Joined: Fri Aug 14, 2015 4:48 pm
- Location: The Nethelands
- Contact:
Re: Modifiying Creality Ender 3 with Plan B
Hello
Plan B firmware does have all the handling for motion and inkjet combined. That is however everything that matches. Also be aware that even now I am not a great programmer, and in the Plan B time I was an even worse programmer. I cannot guarantee that modifying the firmware will be simple.
1. The hardware seems fine and should work
2. Plan B controller is designed for powder machines and has all the handling for powder hoppers. This takes 3 motors and is completely separate from the other motion. It will need to be modified to only handle simple Z.
3. This is my biggest worry. I do not know if the C6602A, a thermal inkjet, and handle UV curing inks. Purely based on feeling I would say you need a XAAR head, a piezo inkjet. Do by all means test it, I am really curious whether it will work, but no guarantees.
4. Seems reasonable, it is indeed a working principle.
You can always ask for advice, but I do hope you have decent programming skills, since you will need to have to modify a fair few things.
Plan B firmware does have all the handling for motion and inkjet combined. That is however everything that matches. Also be aware that even now I am not a great programmer, and in the Plan B time I was an even worse programmer. I cannot guarantee that modifying the firmware will be simple.
1. The hardware seems fine and should work
2. Plan B controller is designed for powder machines and has all the handling for powder hoppers. This takes 3 motors and is completely separate from the other motion. It will need to be modified to only handle simple Z.
3. This is my biggest worry. I do not know if the C6602A, a thermal inkjet, and handle UV curing inks. Purely based on feeling I would say you need a XAAR head, a piezo inkjet. Do by all means test it, I am really curious whether it will work, but no guarantees.
4. Seems reasonable, it is indeed a working principle.
You can always ask for advice, but I do hope you have decent programming skills, since you will need to have to modify a fair few things.
-
- Posts: 3
- Joined: Sun Nov 03, 2019 3:14 am
Re: Modifiying Creality Ender 3 with Plan B
Hi
Thanks for the reply. I understand the main issue is with printing UV inks in thermal cartridges. I went through some literature which suggested that commonly piezo heads are used for UV inks.As a start I am going with the C6602a for testing purposes as its cost effective. In your knowledge are there any piezo heads with the same number of nozzles as the C6602a ? If so, I feel it will be a little convenient to tweak the electronics and the firmware to make the piezo nozzles fire.
Thanks for the reply. I understand the main issue is with printing UV inks in thermal cartridges. I went through some literature which suggested that commonly piezo heads are used for UV inks.As a start I am going with the C6602a for testing purposes as its cost effective. In your knowledge are there any piezo heads with the same number of nozzles as the C6602a ? If so, I feel it will be a little convenient to tweak the electronics and the firmware to make the piezo nozzles fire.
- dragonator
- Site Admin
- Posts: 597
- Joined: Fri Aug 14, 2015 4:48 pm
- Location: The Nethelands
- Contact:
Re: Modifiying Creality Ender 3 with Plan B
I do not know any, since the C6602A is a bit of an odd printhead. The closest thing I know is the XAAR 128, but it already has 128 nozzles, and a serial interface.
-
- Posts: 3
- Joined: Sun Nov 03, 2019 3:14 am
Re: Modifiying Creality Ender 3 with Plan B
Hi
Trying to proceed with the project, I disassembled my HP Deskjet 2131. Is it possible to find whether it is a thermal or piezo inkjet with the attached image? Also, is it possible to read the voltage output from the pins when I try a sample print? I was not able to find any pin layout or details regarding the 2131 online similar to the C6602 and XAAR inkjets.
Trying to proceed with the project, I disassembled my HP Deskjet 2131. Is it possible to find whether it is a thermal or piezo inkjet with the attached image? Also, is it possible to read the voltage output from the pins when I try a sample print? I was not able to find any pin layout or details regarding the 2131 online similar to the C6602 and XAAR inkjets.
- Attachments
-
- Color Nozzle.jpg (192.9 KiB) Viewed 26644 times
-
- Black Nozzle.jpg (144.74 KiB) Viewed 26644 times
-
- Pin.jpg (310.19 KiB) Viewed 26644 times
- dragonator
- Site Admin
- Posts: 597
- Joined: Fri Aug 14, 2015 4:48 pm
- Location: The Nethelands
- Contact:
Re: Modifiying Creality Ender 3 with Plan B
There are few companies that make piezo inkjet. Epson and Xaar almost by definition make piezo inkjet, HP and Canon almost by definition make thermal inkjet. Pinouts are always challenging to find, since this is not open technology.